Fix My Grill Parts finder · repair notes

fix · Weber

Weber Spirit II E-310 igniter replacement

Spirit II E-310 GS4 chassis uses OEM 67053 (button 66220), not Spirit 7642. Three mains, 15.25-inch crossover, AA module under the left table.

moderate PT1H Spirit II E-310Spirit II S-310 Updated 2026-08-31

Igniter electrode gap at a burner port Ceramic insulator, metal tip aimed at a burner port. Spark gap about the thickness of a nickel. SIDE VIEW · ELECTRODE GAP burner tube ports ceramic lead tip spark gap ≈ nickel ~1.8–2.1 mm to a port Tip aims at a port, not the tube wall. Cracked ceramic = replace.
Fig. — Electrode: ceramic, tip, burner port, ~nickel gap.
Two AA cells in the side-table battery well Underside of the left side table. Two AA batteries, polarity stamped in the well. UNDERSIDE · LEFT SIDE TABLE side table (from below) BATTERY WELL AA − + + AA − Two AA cells. Polarity is stamped in the plastic. Reverse = no click. Corroded springs: dry brush, not oil. Then new alkalines.
Fig. — Battery well under the side table. Two AAs. Match stamped polarity.

Spirit II E-310 (2017+ GS4) is not a relabeled original E-310. The cook box, burner rails, and igniter harness are II-specific. Weber’s schematic lists 67053 as the complete AA kit and 66220 as the button. Original Spirit 7642 kits click on a II cart and still miss the GS4 electrode tab.

Do not order Genesis II Infinity parts. Do not order Q 64868. Two-burner II: Spirit II E-210 igniter. Original 310: Spirit E-310 igniter.

Diagnose

Procedure

  1. Tank off. Three grates and five 15.3” bars out. Spirit II E-310 flavorizers.
  2. Photograph collector posts and the color/length of the electrode lead. Aftermarket 67053 kits vary in wire length — your photo is the return argument.
  3. Disconnect the spade at the collector. Unclip the ceramic from the left GS4 tube only.
  4. Vacuum ceramic dust from the rail. A shard shorts the next spark to the box.
  5. Clip the new electrode at the factory tab. Nickel gap. Do not aim at a flavorizer peak.
  6. Seat the 15-1/4” crossover across all three tubes. A Spirit 210 10-1/2” crossover leaves the right main dark.
  7. Two fresh AAs. Lid open. Snap, then left-knob start, then walk middle and right open.
  8. Side burner (if equipped) has its own short lead. Mains light, side dead → that lead only.

When to stop

FAQ

Is Weber 67053 the same as 7642?

No. 7642 is original front-control Spirit 210/310. 67053 is Spirit II 310 (2017+). Button 66220 and electrode 67055 live in the II kit.

Do I need three electrodes on a Spirit II E-310?

Usually no. One left ceramic plus a 15-1/4” crossover lights all three mains. Three ceramics means you are looking at a different family (often Genesis II).

Not affiliated with Weber.

Related notes

Replace Char-Broil burner tubes

Pull stamped Char-Broil tubes, match length and inlet, reseat on the orifices, and leak-check. Universal tubes that are short are how flashbacks start.

Replace Char-Broil heat plates

Measure tent length and width on Performance and Commercial carts. Heat plates are the drip shields — when they lace, burners die. Do not buy by lid name alone.

Char-Broil igniter replacement

Box-store Char-Broil Performance and Commercial carts: piezo versus AA collector, electrode clips on stamped burners, and why the side burner is a separate lead.

How to find your grill model and serial number

Where rating plates live on Weber, Char-Broil, Nexgrill, and Traeger, what to photograph, and how to use the number in the parts finder without guessing from the lid badge.